langfeng, Author at Metal carbide powder,TiC cermet rod,TiCN cermet rod,Titanium oxide,cutting wheel - Page 13 of 15 Archive - Metal carbide powder,TiC cermet rod,TiCN cermet rod,Titanium oxide,cutting wheel - page 13
Welcome to visit our website
Search:

Author Archive

Planetary ball mill operating instructions

Posted on: 三月 30th, 2016 by langfeng No Comments

planetary ball mill 1

According to Planetary ball mill principle, The steps are follows:

 

Step 1: Check accessories and packaging inspection, power on to test machine .

Step 2: Put into the grinding balls and materials, pay attention to the application of balls with large, medium and small sizes, the large ball are used for crushing the material and scattered small balls, small balls for mixing and grinding samples.

Step 3: Install grinding jars tightly to avoid spilling materials and , pay attention to the milling canned firm, avoid milling process from mill pot holder pot to prevent the material spilled, milling tank damaged.

The fourth step, standby power, after the equipment power, have open air switch, safety switch.

The fifth step, set the drive parameters.

The sixth step, abrasive, according to the material, the user requirements, after setting the function parameters of the inverter, tightly cover and start the run button to start the abrasive.

Seventh step, stop unloading tanks, materials After grinding, press the stop button, unplug it.

The eighth step, unloading, open the cover, loosen the hex nut with a wrench, removed the T-screw, pole, gaskets, remove the mill pot.

The ninth step, unloading, the tank material and milling balls poured into a small plugs, grinding balls and material separation with a plug and then plug once the material separation.

Finally, the materials needed to pour the sample bag. The tenth step, cleaning equipment, the mill pot and balls cleaned with a rag to wipe the device from the inside to the outside clean. These are the planetary ball mill operating instructions and precautions outlined hope customers can follow the correct procedure, so as to enhance the effect of reducing planetary ball mill planetary ball mill failure.

 

Stay tuned for detailed product information company official website:http://www.langfengmetal.com/, please contact: postmaster@metalcarbidepowder.com

Lang feng metallic “going out” strategy has achieved initial success

Posted on: 三月 30th, 2016 by langfeng No Comments

Lang Feng has always stands up the world of corporate mission to create value for customers, help employees grow and help more people to progress and development as our firm goal to focus on military rocket systems and new materials, coating materials, carbide, metal ceramic cutting tools, drilling tools and materials research and development, production and sales. In March this year, the International Hardware Fair in Cologne, Germany, Lang Feng Mr. Liu Zhaohui led the export manager Zhang Lu and foreign trade Zou Lan participated in the exhibition. Recently, the Ministry of Foreign Trade inquiries increased steadily, production and sales of various products presented to pick up momentum, orders from Australia, Germany, Italy, Britain, India and other countries on all continents. Lang feng trip “going out” strategy for the formation of new advantages to participate under Economic Globalization international economic cooperation and competition has laid a solid foundation.

tic rod

The International Hardware Fair event shows the product manual hand tools, electric tools (hand-held, stationary) and accessories, machine tools and other industrial products, as well as business services and other industries in industrial products. Our company exhibited metal carbide powder, high speed steel twist drill, titanium carbonitride cermet rod, tile cutter wheel glass cutter wheel and other metal products, won critical acclaim.

cutter wheel

tic-based-rod

zrc powder

Stay tuned for detailed product information company official website:www.langfengmetal.com, please contact:postmaster@metalcarbidepowder.com

The case of Tungsten carbide, titanium tantalum niobium solid solution(WC – TiC – TaC – NbC)product application?

Posted on: 三月 29th, 2016 by langfeng No Comments

A solid solution of tantalum and niobium titanium carbide (WC-TiC-TaC-NbC) applies carbide powder additive.

Lang feng metallic research center conducted the following experiment:

With 15% in K10 grade carbide cutting tools in solid solution of tantalum and niobium titanium carbide (WC-TiC-TaC-NbC) powder grades compiled for: K10WTTB, Lang peak metal produced using 1.05 micron D50 K10WTTB, Lot : 2209, the same ingredient in the process, the same pressing process, the same sintering process produced carbide rods for 2-blade cutter for cutting tests, K10 high-speed processing of high temperature wear to 0.2mm, And K10WTTB high-speed processing of high temperature wear is 0.1mm, after we conducted data analysis, the results showed that: a solid solution of tantalum and niobium titanium carbide (WC-TiC-TaC-NbC) was added to the K10 cemented carbide, high temperature performance improvements double wear double, and has good performance red hard.

Tungsten carbide tile cutter wheel

Posted on: 三月 29th, 2016 by langfeng No Comments

Tungsten carbide tile cutter wheel

Introduction:
Titanium-Coated Tungsten-Carbide Replacement Cutting Wheel for manual tile cutters is the perfect replacement part to bring your tile cutter back to like-new performance. Changsha langfeng supply various sizes depends on clients requirement. The wheel is designed for accurate scoring on porcelain and ceramic tile. The titanium-coated tungsten-carbide material is extremely durable, providing accurate cuts on ceramic and porcelain tile over a long life.

 

Advantages of our tile cutting wheel:
 1.stable and reliable quality.
2.made from 100% virgin material;
3.all products go through in-process and final inspection
4.free online technical service available.
5.Sample available.

 

tile cutter wheel techincal data

Ti(C,N)Based Cermet plate

Posted on: 三月 29th, 2016 by langfeng No Comments

ticn Based Cermet plate

Introduction:
Our company production of Ti (C, N) based cermet CNC cutting tools(Grade:LFT15), hardness up to 92.5HRA, strength up to 2.0-2.1Gpa.Grain size less than 0.8 micron,belong to the ultrafine metal ceramics.By adding carbon titanium nitride and other metal and ceramic powder additive,Having a fine structure,can guarantee the quality of the surface of the workpiece in various of cutting conditions.Having excellent thermal shock resistance and the optimal wear resistance and toughness,And having excellent resistance to plastic deformation and bue.
Cermet tool toughness higher than ceramic tools,More wear-resistant than carbide cutting speed faster,machining difficult workpiece material, metal ceramics have excellent surface polishing technology and high speed machining technology.With high-speed finishing and milling technology for low-carbon steel, carbon steel, alloy steel and stainless steel,to achieve superb turning, groove, boring, bearings and milling level.Having chipping resistance and wear resistance superior cermet.Having excellent thermal conductivity and wear resistance,is steel processing the best choice,suitable for steel turning, groove, boring, bearings and milling.Covering a wide range of steel finishing to roughing field.

 

Application:
The Cermet bars with long tool life in high-speed finishing process.Compared with coated carbide, more suitable for light cutting (finishing).At the same cutting condition, can obtain stronger abrasion resistance and surface precision.
Solid cermet plate can be used for making varioius drill bits, automobile special cutter, printed circuit board ,special cutters, engine special cutters, horologe,processing special cutters, integral vertical milling cutter, graver,core bar and perforation toolsand etc. 
The Solid cermet plate are used for cutting aluminum alloy , cast iron , stainless steel , refractory alloy steel ,nickel-based alloy , titanium alloy and non-ferrous metal , various carbide grades with stable properties have been widely recongnized by worldwide tool makers. 

 

Ti (C, N) Based Cermet plate technical data1

Ti (C, N) Based Cermet plate technical data2

Ti(C,N)based cermet rod with one central coolant hole

Posted on: 三月 29th, 2016 by langfeng No Comments

ticn based cermet rod with one hole

Introduction:
Our company production of Ti (C, N) based cermet(Grade:LFT15), hardness up to 92.5HRA, strength up to 2.0-2.1Gpa.Grain size less than 0.8 micron,belong to the ultra-fine metal ceramics.By adding carbon titanium nitrite and other metal and ceramic powder additive,Having a fine structure,can guarantee the quality of the surface of the work piece in various of cutting conditions.Having excellent thermal shock resistance and the optimal wear resistance and toughness,And having excellent resistance to plastic deformation and bur.
Cermet tool toughness higher than ceramic tools,More wear-resistant than carbide cutting speed faster,metal ceramics have excellent surface polishing technology and high speed machining technology.With high-speed finishing and milling technology for low-carbon steel, carbon steel, alloy steel and stainless steel,to achieve superb turning, groove, boring, bearings and milling level.Having chipping resistance and wear resistance superior cermet.Having excellent thermal conductivity and wear resistance,is steel processing the best choice,suitable for steel turning, groove, boring, bearings and milling.Covering a wide range of steel finishing to roughing field.
Metal ceramic hardness is higher than that of sintered hard alloy materials,compared with cemented carbide.Ceramic metal and black metal work pieces are of low affinity under high temperature conditions,can get a better surface finish,from low speed to high speed processing is possible.
Application:
Having long tool life in high-speed finishing process.Compared with coated carbide, more suitable for light cutting (finishing).At the same cutting condition, can obtain stronger abrasion resistance and surface precision.
 Solid cermet rods can be used for making varioius drill bits, automobile special cutter, printed circuit board ,special cutters, engine special cutters, horologe,processing special cutters, integral vertical milling cutter, graver,core bar and perforation toolsand etc.
 The Solid cermet rods are used for cutting aluminum alloy , cast iron , stainless steel , refractory alloy steel ,nickel-based alloy , titanium alloy and non-ferrous metal , various carbide grades with stable properties have been widely recongnized by worldwide tool makers. We can produced the ungrounded and grounded carbide rods.

ticn based cermet rod technical data

ticn based cermet rod technical data2

Ti(C,N)Based Cermet Rod

Posted on: 三月 29th, 2016 by langfeng No Comments

ticn based cermet rod2

Introduction:
We provide Ti (C, N) cermets based CO and Ni as the basic material, with super hardness, low-coefficient of friction, good wear resistance and other advantages; in the cutting process can effectively avoid sticking knife, scratches and cutting modulation and other processing defects with high cutting speed; good flank wear resistance allows the tool at high speed cutting remains a longer tool life, and help remove chips achieve high precision machining.  
High hardness resutlt in efficiency & precision processing,longer service life  help reducing cost.

 

Application:
Drill bit;milling cutter;welding part; welding blade CNC tools for stone cutting drilling tools ;cast iron sheet metal, parting inserts, expandable reamers parting inserts, cermet rods, expandable reamers Work Hard Tools,drill Rods and drill Pipes, steel blank for core bit; PCB micro-drilling tools; CNC router bits; CNC end mill ball; CNC turning inserts; Perforated rod (reamer) do reamer drilling;etc . 

TI(C,N) BASED CERMET ROD technical data
ti(c,n)based cermet rod technical data (2)

Titanium Carbonitride Powder

Posted on: 三月 29th, 2016 by langfeng No Comments
Ti(C,N) powders
Molecular weight:121.75
Density:5.43g/cm3 at 25°C(lit.)
Melting point: >350°C(lit.)
Titanium carbonitride has the appearance of a charcoal grey powder.  It has a high melting point, high hardness, excellent anti-oxidation ability, ductility, lubricity and wear-resistance.  Compared with titanium carbide, titanium carbonitride has lower friction coefficient and higher hardness, which improves the quality and lifetime of titanium carbonitride coated tools. Since TiN TiCN lower than the coefficient of friction and a higher hardness of the TiCN coating is more suitable for cutting tools such as stainless steel, titanium and nickel alloys and other hard materials, more wear resistance and high temperature stability, significantly improve tool life.
 
Performance and technical
Titanium carbide nitrides make the cermet has the following characteristic: Degree of hardness (HRA) reaches as high as 91-95, then achieves the nonmetallic ceramic cutting tool's degree of hardness level; Has the very good resistance to wear and ideal anti-crescent moon hollow attrition ability, when high-speed cutting steel materials the rate of wear is extremely low, its resistance to wear compared to WC base hard alloy high 3-4 times; Has the high thermal stability, high temperature degree of hardness, the strength at high temperatures and the high temperature resistance to wear is quite good, still could carry on the cutting under 1100-1300°C the high temperature, generally cutting velocity compared to WC base hard alloy high 2-3 times; Has the good chemical stability and high oxidation resistance ability; Compares with the hard alloy, Titanium carbide nitrides cermet has the very high resistance to wear, the oxidized degree to be lower, the heat-resistant knocking to be able to be better, suitable to serve as the high-speed cutting cutting tool material, can the very good control work piece GDOP and the common difference, the smooth finish is high, feed velocity higher; Processing carbon steel, stainless steel, micro alloy steel, as well as modular cast iron time can make the very good progress.

Planetary ball mill operating instructions

Posted on: 三月 24th, 2016 by langfeng No Comments

Step 1: Check accessories and packaging inspection, power on to test machine .
Step 2: Put into the grinding balls and materials, pay attention to the application of balls with large, medium and small sizes, the large ball are used for crushing the material and scattered small balls, small balls for mixing and grinding samples.
Step 3: Install grinding jars tightly to avoid spilling materials and , pay attention to the milling canned firm, avoid milling process from mill pot holder pot to prevent the material spilled, milling tank damaged.
The fourth step, standby power, after the equipment power, have open air switch, safety switch.
The fifth step, set the drive parameters.
The sixth step, abrasive, according to the material, the user requirements, after setting the function parameters of the inverter, tightly cover and start the run button to start the abrasive.
Seventh step, stop unloading tanks, materials After grinding, press the stop button, unplug it.
The eighth step, unloading, open the cover, loosen the hex nut with a wrench, removed the T-screw, pole, gaskets, remove the mill pot.
The ninth step, unloading, the tank material and milling balls poured into a small plugs, grinding balls and material separation with a plug and then plug once the material separation. Finally, the materials needed to pour the sample bag.
The tenth step, cleaning equipment, the mill pot and balls cleaned with a rag to wipe the device from the inside to the outside clean.
These are the planetary ball mill operating instructions and precautions outlined hope customers can follow the correct procedure, so as to enhance the effect of reducing planetary ball mill planetary ball mill failure.

ND planetary ball mill Introduction

Posted on: 三月 24th, 2016 by langfeng No Comments

small valume planetary ball mill (1)

Purpose:
Planetary ball mill applied to universities, colleges, research institutes and corporate laboratories to study rapid batch grinding to colloidal fineness of the sample (minimum of up to 0.1μm), and mixed, homogenized and dispersed. Widely used in mining, soil, metallurgy, electronics, electricity, materials, chemical light, medicine, beauty, environmental protection, ceramics, glass, nuclear research and other scientific and industrial sectors.

Principle:
Planetary ball on a turntable equipped with a total of four milling tank, when the turntable rotates, when the canister is constantly milling around the turntable axis continuous revolution, will continue to work around its own axis reverse rotation of planetary motion, tanks balls collide with each other as well as materials, friction, to crushing, grinding, mixing, dispersing the sample object, and sustained high-speed motion.
Way of working:
Planetary ball mill can be dry, wet, vacuum mill. It Yung mixing finely ground, sample products, product trial as a whole, and one can be sampled at the same time, the ideal tool for both development of new materials, as well as the necessary equipment for the production of small batch grinding special materials.
Control System:
Using the most advanced frequency control has a program setting function, you can achieve continuous unidirectional, continuous commutation timing way, the timing change to the four-way programmable operation.
Program control using the AC motor (no carbon brush wear, long life, low starting power, energy-saving, can set the program to run), machine integration, small size, light weight, low noise, simple operation, without strict balance to operate.
ND planetary ball mill advantages:
The appearance of the original clamshell box (or open type), easy to operate, cover with safety switch, safe and reliable.
Compact, attractive appearance, greatly reduce the weight and yet stable, truly a fully integrated whole.
Planetary gear train transition from the 4 wheel increased to eight, increasing the stability of the drive (especially at change of direction), reducing wear and extending the life of the machine.

Stay tuned for detailed product information company official website:www.industryequips.com, please contact: angela@metalcarbidepowder.com